Vehicles
25 not categorized PORSCHE 996T SILICONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.91450411710 Our own excellent reproduction of this no longer available part is a must for proper engine cooling. install easily with a little silicone grease, fits the rear of the engine bay only. View/Change Diagram
$37.10
Make a selection 90042349800 Includes silicone bronze replacements for: 2 - 901 423 253 00 accelerator, 2 - 911 423 341 01 clutch shaft, 2 - 901 423 343 00 clutch clevis, 2 - 911 423 542 00 brake, 1 - 900 309 002 00 roll pin General Fitment911 1965-69911 1970-73 911 1974-77 911 1978-83 911 1984-86 911 1987-89 912 1965-69 914 1970-76 930 1975-77
From $39.99
Make a selection 91442459100 These are the very necessary boots that fit at the rear caliper end of the emergency brake cable. you probably did not know that they existed because yours have been gone for so long! easily installed with a little silicone grease. we also have the cable pin and clip available. View/Change Diagram
From $6.25
Make a selection 47407355 Replaces worn and defective accelerator pump diaphragm to eliminate hesitation and stumble during acceleration. Fits just like original parts. Manufactured from fuel resistant, rubber membrane with silicon bronze center plunger hardware. Fits weber 32-36 dgv 5a / 32/36 dgev 38mm
$21.50
Make a selection 919108 Magnecor’s kv85 competition (8.5mm) and r-100 racing (10mm) ignition cables feature magnecor’s exclusive 2.5mm high capacity metallic inductance emi suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of magnecor’s exclusive tc-1500-hs high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket’s insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. General Fitment911 1974-77930 1975-77 911 1978-83
$331.10
Make a selection 91453187310 This nifty item squeezes the water from the side of the window glass and also prevents water from entering the door cavity. easily inchwormed into the gutter using silicone grease order a rear window cap to finish the job. View/Change Diagram
From $6.89
Make a selection 91453118510 This is an exact reproduction of the original factory seal that fits on the drivers side of the hardtop and the one that the side glass rolls up and hits. easily replaced with a wide blade screw driver and some silicone grease just fit the inner side into the channel and then pinch the outside in with a screwdriver. remember not to cut it short as it will shrink to fit! direly needed to seal the wind and water out of your 914 View/Change Diagram
From $40.81
Make a selection 91463193900 These very correct factory color custom made factory identical seals were never available from the factory as an individual part. These are much higher quality than the original and even some other after market repros. seal the tail light lense to the tail light body providing a comfortable wear-free seat for the valuable lens and keeping the water out of the assembly. sold as a set and easily installed. if you have a water leak into the rear trunk, then simply remove the tail light body and reseal the tail light body to the rear panel with some silicone sealant. General Fitment914 1970-76
$15.37
Make a selection 91455926710 The finishing touch to the rocker panel installation and protects the jack tube from rust. Two required snaps in. good to put a little silicone grease on before installation View/Change Diagram
From $6.30
Make a selection 99970146840 Note: this brand is red silicone material. View/Change Diagram
From $3.45
Make a selection 919222 Clewett engineering high performance ignition wires are 8mm, with a 2 layer silicone jacket, inside a 1200 degree protective sleeve. This spiral core, resister conductor wire provides emi/rfi suppression for all ignition and engine management systems. These wires are a great choice for racing or street applications. Red and black are standard colors. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$209.00
Make a selection 919228 Clewett engineering high performance ignition wires are 8mm, with a 2 layer silicone jacket, inside a 1200 degree protective sleeve. This spiral core, resister conductor wire provides emi/rfi suppression for all ignition and engine management systems. These wires are a great choice for racing or street applications. Red and black are standard colors. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$209.00
Make a selection 919233 Clewett engineering high performance ignition wires are 8mm, with a 2 layer silicone jacket, inside a 1200 degree protective sleeve. This spiral core, resister conductor wire provides emi/rfi suppression for all ignition and engine management systems. These wires are a great choice for racing or street applications. Red and black are standard colors. General Fitment944 1989-91944 1985-88
$145.60
Make a selection AP955110 Agency power has developed a new cold air intake kit for the v8 Porsche Cayenne. dubbed "the stealth" system, the agency power cold air intake adds power to your Cayenne s or GTS from 03-11. the intake kit is designed to replace the entire factory airbox from the maf tubes to the filter. each intake tube is hand made here in the usa using precision jigs with 6061 aluminum that is tig welded. the intake tubes attach to the factory maf sensor with the supplied silicone coupler. each intake tube features a custom spec'd K&N cone filter with front inlet to draw air in from the OEM ducting. because of the close proximity to the engine, we also include OEM mounted heat shields that securely connect the intak...(choose a part on the right to read more) General FitmentCAYENNE 2007-10CAYENNE 2003-06
$695.95
Make a selection 996TTHFPPPB The automotive speed technologies 996 tt fresh air intake plenum and hard inlet pipe kit is designed to enhance the performance of your Porsche 996 tt by allowing fresh air to flow freely to the turbos for quick spool and additional power - very important for modified cars running larger than OEM turbos or running high boost. The system consists of the speedtech hi-flow intake plenum with 70mm outlet tubes, attached to 70mm molded hard plastic tubes for uniform high flow. Silicon hose is supplied to connect to the turbo inlets. The speedtech hi-flow plenum is designed to flow more air than the OEM plenum and deliver it quickly and smoothly with no restrictions from the maf tube all the way to the turbo inlets. ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05
$2,551.50
Make a selection AC5005 The newest concept in maintaining a flawless finish without rewaxing.
$22.72
Make a selection AP996TT108 As you step up the power level on your 996 turbo, having proper cooling efficiency is mandatory to maximize your turbo performance. Street and track cars will heavily benefit from the use of our upgraded intercoolers. The factory Porsche intercooler core is great, but their end tanks are what is lacking. Agency power has developed these complete intercooler replacements for your Porsche 996 turbo. The intercoolers require some modification to the intercooler frame and vehicle. General Fitment911 TURBO/GT2 2001-05
$1,749.95
Make a selection AP997TT108 As you step up the power level on your 997 turbo, having proper cooling efficiency is mandatory to maximize your turbo performance. Street and track cars will heavily benefit from the use of our upgraded intercoolers. The factory Porsche intercooler core is great, but their end tanks are what is lacking. Agency power has developed these complete intercooler replacements for your Porsche 997 turbo. Some modifications are required to the intercooler frame and vehicle for fitment. General Fitment911 TURBO/GT2 2001-05
$1,749.95
Make a selection 91453187410 This nifty item squeezes the water from the side of the window glass and also prevents water from entering the door cavity. easily inch-wormed into the gutter using silicone grease; order a rear window cap to finish the job. View/Change Diagram
From $6.89
Make a selection FSPOR970TICP Every little bit helps and that is why fabspeed has designed stainless steel intercooler piping for the Porsche panamera. They saw that the OEM 2.3"/58mm silicone hose and knowing that he stock silicone hose will expand as pressure builds was just not going to cut it for the the panamera. That engine deserves something more beefier reliable and thats what fabspeed did by increasing the size to 2.75"/70mm and making od t304 stainless steel the fabspeed tube will retain a rigid structure allowing for maximum air intake even at full boost. What makes this also a great add on is the direct bolt-on replacement intercooler tubing for improved air intake into the intercoolers. General FitmentPANAMERA 2010-14
$1,302.95
Make a selection FVD211622 This silicone hose supplies hot air to the heater control box, it replaces original part # 930 211 622 01. It runs from the exhaust heat exchanger to the heater control box. We recommend replacing the heater box clamp, part # 90121105122 on one end and a hose clamp part # 99951234902 on the other end. Sold individually. 2 necessary per car.
$52.80
Make a selection SCINCRSC0096 Increase the airflow and horsepower of you Porsche 996 or 997 in a few easy steps. Schnell's 4 ply, silicone hose will allow for much better airflow while still protecting your air box from costly backfires, unlike the competition. The silicone material does not retain heat which can rob your Porsche 996 and 997 engine of valuable horsepower. This intake installs in less then 15 minute. General Fitment911 1998-05911 2005-08
$160.65
Make a selection FVD424049I Numeric racing high performance shifter cables can transmit additional noise and vibration inside the cabin. These silicone insulation tubes are designed to reduce the intrusive cabin noise. We recommend them for any street car. Sold as a set. 1 set accommodates one set of numeric racing high performance shifter cables. Instructions: cut the tube in a spiral so that you don't need to use any zip ties to hold it on. One twist per foot will work just fine. It is also important that you reuse the rubber grommet that hold the cables in the firewall.
$35.20
Make a selection MGCW3 Magnecor’s kv85 competition (8.5mm) and r-100 racing (10mm) ignition cables feature magnecor’s exclusive 2.5mm high capacity metallic inductance emi suppressed conductor consisting of stainless steel wire precisely wound at 200 turns per inch over a ferrimagnetic core. The insulating jacket is made entirely of magnecor’s exclusive tc-1500-hs high strength aerospace grade silicone rubber, and its single layer construction will prolong the jacket’s insulating ability by conducting extreme heat away from hot-spots that occur near over-the-limit heat sources. General Fitment911 1984-86911 1987-89
$192.33
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |